Geiger Kanaltechnik Invests in the Newest Smart Pipe Robot Made by Pipetronics» Read more
PI.TROC21 injection resin
The epoxy resin PI.TROC21 has been specially developed for side inlet rehabilitation. It is characterised by a very high viscosity and is distributed particularly quickly and evenly. The transparent form work of the PI.TRON injection system clearly shows how the resin flows continuously and how cavities are filled.
Description – Detail
PI.TROC21 is a paste-like epoxy resin system from Pipetronics. It consists of two components. The area of application is the robot-supported rehabilitation of nozzles and pipe inlets in form work technology.
We offer PI.TROC21 in two curing agent variants: The Basic curing agent variant cures at an ambient temperature of 20°C within 3 hours. The Rapid curing agent version cures within 1.5 h at an ambient temperature of 20°C.
PI.TROC21 is available in 700 ml aluminium tubular bags. These are not only perfectly matched to the capacity of the resin cartridge of the PI.TRON filling and injection system, but can also be mixed quickly and easily in the specially developed SAM700 mixing and metering station in the quantities required for the respective application.
For the large cartridge with 2.8 l and a mixing ratio of 3:1, which has a total of four tubular bags of 700 ml each, the optimally mixed resin can be produced in a single process.
In addition, we offer PI.TROC21 in the 2.8 l tin.
The advantages at a glance:
- Excellent flow behaviour
- High chemical and mechanical resistance
- Maximum adhesion on damp and dry surfaces
- Shrinkage and crack-free curing
|Mixing ratio:||Resin: curing agent 3:1|
|Specific gravity (mixture):||approx. 1,2 g/cm³|
|Chemical resistance:||ph 2 to ph 12|
|Pot life (at 20°C):||with PI.TROC21 R (rapid): 25 minutes|
with PI.TROC21: 40 minutes
|Moulding time (at 10°C):||with PI.TROC21 R (rapid): 3.5 h |
with PI.TROC21. 8 h
Full chemical resistance: after 7 days
|Form of delivery:|
PI.TROC21.7 / PI.TROC21.7 R (rapid)
Surface pretreatment: The substrate must be clean and free of all loose parts, dust, oil, grease, or other separating substances. It can be dry or damp. The base must be load-bearing and have the generally required tear strength of 1.5 N/mm2.
Mixing: PI.TROC21 resin and curing agent are supplied in matched quantities in tubular bags or tins. Ideally, both components should be homogeneously mixed using the four-component paste mixing unit with SAM700 compulsory mixer in a ratio of 3:1 (resin: curing agent). Complete emptying of the containers is indispensable for maintaining the mixing ratios and is necessary for ecological reasons.
Processing: PI.TROC21 is usually inserted into the nozzle to be rehabilitated using robot technology such as the PI.TRON form work and injection system. The form work technology is used for this purpose.
*Unless otherwise stated, these data apply to a temperature of 20°C and a relative humidity of 50%.
PI.TROC21 injection resin
Your contact partners for ordering resins
Service centre Rheda-Wiedenbrück
Contact partner: Yilmaz Saglam
Phone: +49 5242 183 899-0
Service centre Gelsenkirchen
Contact partner: Heinrich Colkos
Mobile: +49 (0) 170 454 58 37
Service centre Röthenbach
Contact partner: Matthias Kast
Phone: +49 (0) 911 477 192 - 17
Mobile: +49 (0) 151 5716 70 74